Zephyr CPA-E42ASX Guía de instalación

Use, Care, and Installation GuideModel number:Numéro de modèle: ____________________________________Número de modelo:Serial number:Numéro de série: __

10Installation - Ductwork Calculation Sheet3 1/4 ” x 10”Rect.,straight6 ” Round,,straight7", 8”Round,,straight3 1/4 ” x 10”Rect.90°elbow3 1/4 ”

11www.zephyronline.comInstallation - Preliminary OperationsAttention! The installation requires several stepswhere is asked to temporarily remove some

12Installation - Internal BlowerNote: for External blower installation disregard theinstruction in this page and step ahead on page 14.TOP DISCHARGE(V

13www.zephyronline.comINTERNAL BLOWER INSTALLATION• Fit the blower inside the hood.• Install the blower to the support with 4 screws(Provided), check

14• Install the supplied round transition collar to thepreviously installed cover/round transition supportplate from inside the hood. Align and attach

15www.zephyronline.com• Install the supplied round transition collar to thepreviously installed cover/round transition supportplate. Align and attach

16• To attach front panel to hood body, align the 8 threaded studs through the front bodies corresponding holes.Use 8 wing nuts to attach and secure.

17www.zephyronline.comInstallationINSTALLING THE HOOD ONTO THE WALL1. Disconnect and move freestanding or slide-in rangefrom cabinet opening to provid

1813. Optional duct cover installation:a. Remove the support bracket from the Duct Coverassembly and attach it to the ceiling with 2 drywallanchors an

19www.zephyronline.comInstallation - Hanging the Hood onto the Wall14. For internal blower installation ONLY:a. Horizontal (Rear) discharge:Install fr

2PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.IMPORTANT: Save these Instructions for the Local Elec

20Installation - Electrical Connection & Final Installation Steps18. Electrical connectionWARNINGElectrical Shock HazardWarning: Turn off power ci

21www.zephyronline.comDescription of the Hood1 Controls2 Baffle filter3 Halogen lamp4 Incandescent ambient lamp5 Hood body6 Duct cover62233415

22 Features & Controls - Touch Controls & FeaturesUse the high suction speed in cases of concentrated kitchen vapors. It is recommended that

23www.zephyronline.comFilter Clean Reminder (Standard Baffle Filters fitted):A set of baffle filters are fitted by the factory. These Baffle Filters a

24MaintenanceBAFFLE FILTERThis must be cleaned once a month using non abrasi-ve detergents, either by hand or in the dish-washer,which must be set to

25www.zephyronline.comMaintenanceREPLACING THE MOOD LIGHTING BULB:To replace mood lighting bulb, remove baffle filter fromhood.To access lamp area, re

26Trouble ShootingAfter installation, theunit doesn’t work?Light works, but motoris not turning.The unit is vibrating.The motor is working,but the lig

27www.zephyronline.comList of Parts and AccessoriesPart Description Part#Internal Blower 600 CFMExternal Blower 1000 CFMHalogen Bulb, 120V 50 WF

3www.zephyronline.comTable of ContentsImportant Safety Notice ...5Electrical & In

4Installation - Installing the Duct Covers ... 18Installation - Hanging the Hood onto the Wall ...

5www.zephyronline.comImportant Safety NoticeCAUTIONFOR GENERAL VENTILATING USE ONLY. DO NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS ORVAPORS.W

6Electrical & Installation RequirementsELECTRICAL REQUIREMENTSIMPORTANTObserve all governing codes and ordinances.It is the customer’s responsibil

7www.zephyronline.comList of MaterialsPARTS SUPPLIED• Hood body, with stainless steel baffle filter and halogen light bulbs and incandescent lamp alre

8Dimensions and ClearancesOnly for version with top discharge feature:* Hood with external motor: Over this measurement a hole may be made on the rear

9www.zephyronline.comDucting Options and ExamplesClosely follow the instructions set out in this manual.All responsibility, for any eventual inconveni