Zephyr AK7036AS Guía de instalación Pagina 1

Use, Care, and Installation Guidewww.zephyronline.comModel number: Serial Number: Date of Purchase: Sales Dealer: MAY12.0701 © 2012 Zephyr Corporation

8www.zephyronline.comInstallation – Specifi cations1 3/16”8 9/16”1 3/16”2 3/16”2 3/4”3”27 7/8” (30”)33 7/8” (36”)39 13/16” (42”)29 15/16”

9ELECTRICALWARNINGAll Electrical work must by performed by qualifi ed electrician or person with similar technical know how and background.For personal

10www.zephyronline.comInstallation – Mounting the Range HoodFor dual blower installation instructions please refer to page 13.If recirculating range h

11This range hood is equipped standard with a 6” round vertical duct option. To convert from 6” round vertical to 3-1/4” x 10” horizontal ducting ple

12www.zephyronline.com6. On the back of the hood, remove the (6) screws holding the rectangular cap. 7. Place round to rectangular transition adap

131. Disconnect single blower wire.2. Remove support screw from top of hood near the back. Remove 2 screws holding blower plate to hood to release b

14www.zephyronline.comInstallation – PBD-1100A Dual Blower7. Secure dual blower plate to hood by following removal instructions in reverse. Attach bl

15Accessory Installation – Heat Lamp Kit1. Remove nuts from each of the (4) screws around the bottom panel. Remove bottom panel.2. Replace bottom pa

16www.zephyronline.comFeatures & Controls – Touch Controls & FeaturesFThe standard baffle filters are required to be cleaned frequently and as

Features & Controls – Touch Controls & Features17Charcoal Filter Change Reminder (charcoal filter, if installed)When your hood is installed as

www.zephyronline.com

Features & Controls – Touch Controls & Features18www.zephyronline.comBaffle Filter Clean Reminder Whether your hood is installed as an exhaust

19SURFACE MAINTENANCE:Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent, or steel wool/scouri

20www.zephyronline.comREPLACING LIGHT BULBSCAUTION: Light bulb becomes extremely hot when turned on.DO NOT touch bulb until switched off and cooled. T

Troubleshooting21TROUBLESHOOTING PROCEDURES FOR TEMPEST IIssue Cause What to doAfter installation, the unit doesn’t work.1. The power source is not t

22www.zephyronline.comDESCRIPTION PART # Replacement PartsLight Bulb MR16 (GU10) 35W (each) Z0B-0023Baffl e Filter (e

1-888-880-8368STAPLE YOUR RECEIPT HERETO OBTAIN SERVICE UNDER WARRANTY OR FOR ANY SERVICE RELATED QUESTIONS, please call: Zephyr Corporation (refe

1SAFETY NOTICE ... 2-3LIST OF MATERIALS ...

Important Safety NoticeREAD AND SAVE THESE INSTRUCTIONS2www.zephyronline.comWARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN

Important Safety Notice3WARNINGTO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.CAUTIONTo reduce risk of fi re and to properly exhaust air outside -

List of Materials4www.zephyronline.comMODELS: AK7000AS, AK7036AS, AK7042ASPARTS SUPPLIED1 - Hood2 - Baffl e fi lters (3 - AK7036AS and AK7042AS)2 - Halo

5Installation – Ducting Calculation SheetDuct piecesTo t a lEquivalent numberlength x used =3-1/ 4” x 10”Rect.,straight1 Ft. x ( ) =

Installation – Mounting Height & Clearance6www.zephyronline.comDUCTINGA minimum of 6” round or 3-1/4” x 10” rectangular duct must be used to maint

7WARNING FIRE HAZARDNEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be